综合久久影院-综合久久伊人-综合久久一区二区三区-综合久久五月天-亚洲欧美日韩国产一区图片-亚洲欧美日韩国产一区二区三区精品

Muen
News

News

Enterprise service provider

location : Home > News > Technical information

Use your inverter with the right power

2023-05-20 13:07:17

Low voltage fault


The VFD reports a low voltage fault when the DC link voltage of the drive drops below 62% of the nominal level at the high setting (480 VAC) and 50% of the nominal value of the low setting (400 VAC).


The + 10% and - 15% voltage tolerances in most manuals are recommended operating ranges to allow the driver on hand to maintain high efficiency and proper motor current. The drive can be below these tolerances, but the reduced voltage can have unpredictable effects on motor current, motor temperature and overall performance.


More specifically, if the line voltage parameter of the driver is set to high and 480 VAC is being applied, the driver will generate a low voltage fault when the DC link voltage drops to 62% of the nominal - e.g., 480 VAC · 0.62 · √ 2 = 421 VDC. The nominal DC link voltage is 480 VAC · √ 2 = 679 VDC.


Notes on switching


Although it is generally accepted to switch VFD from line supply to standby generator in many applications, there are some limitations. Most importantly, the phase to phase voltage input voltage swing of many portable standby generators is greater than the phase to phase voltage tolerance recommended by the driver, usually less than 2%. To prevent voltage oscillations, VFDs are equipped with surge protectors in the input rectifier circuits - but external protection (e.g. surge arresters) may be required for severe input disturbances. Large variance will produce large ripple on DC bus capacitance, which will cause capacitor and other power components to be damaged over time.


Another potential problem arises when switching from line power to standby generators. Most drivers take at least two minutes to power up again; failure to follow this guideline may damage the charging relay circuit, or at least damage the input fuse or trip the circuit breaker.


3% line reactor may improve the current surge caused by moderate input power voltage.


Another solution is to add a voltage monitor with an appropriate time delay. They have protection trip levels to shut down the drive in the event of under voltage, over voltage, loss of phase and phase to phase voltage imbalance. These devices ensure that the VFD is not exposed to unbalanced input power or power up until the voltage is within tolerance and the appropriate delay time is met.


Isolation transformer


The final recommendation - the most expensive solution - is to use isolation transformers. This ensures complete isolation of input power issues associated with grounding and noise that may affect the drive. Does isolation transformer provide better protection than line reactor? Yes. When does the application need isolation transformer? This type of transformer is recommended when installed close to the substation.


There are many advantages in inserting driver isolation transformer between VFD and its power supply. Isolation ensures that there is no direct electrical connection between the source and the load - but for any transformer other than an autotransformer. The unique feature of the drive isolation transformer is the grounding electrostatic (Faraday) shield placed between and around the primary and secondary windings. This shielding reduces the capacitance coupling involved in the transmission of common mode voltage interference by one million times. Without this shielding, the capacitor allows high frequency noise and transient voltage spikes to pass through the transformer.


Common mode transients are transients that occur between the ground and the neutral point of an AC system. Although the two parts of a circuit are usually combined at one point, they cannot be considered to have the same potential throughout the power system. The common mode transient interference results from the normal operation of switching power supply, driver operation, arc welding machine, lightning, and even stepping motor. Some isolation transformers also prevent "normal mode" transients between the line and neutral.


Consider an application in which the daily utility power supply of a substation capacitor bank in an industrial park causes a transient voltage spike - amplified by reflection of field capacitors in a nearby factory. Suppose a facility in the park has several small drives rated at 7.5 HP. Normal mode transients can cause these drives to shut themselves down, resulting in costly process downtime. This interruption can be prevented by isolating the transformer.


Frequency converter manufacturer


label

QR code

The public,

Mobile station
The public, Mobile station

Contact

未標(biāo)題-8.png 0755-81719517
未標(biāo)題-10.png0755-81719530 未標(biāo)題-11.pngamb@ambition.com.cn
未標(biāo)題-12.pngFloor 1, 5 and 6, building 7, lijincheng science and technology industrial park, gongye dong road, longhua new district, shenzhen

Navigation

Home          About

Product      Case

Solution      Service

Job      News

Contact          

Copyright © Shenzhen Ambition Electronic Co., Ltd Record number:備案號:粵ICP備12045920號
主站蜘蛛池模板: 玖玖在线免费视频 | 日本强日本不卡一 | 蜜柚视频 在线 | 久久777国产线看观看精品卜 | 欧美精品久久一区二区三区 | 日韩在线综合 | 中文字幕中国女同互慰视频 | 国产一级淫片免费播放 | 九九热国产精品视频 | 在线精品自拍亚洲第一区 | 男女做视频网站免费观看 | 成人午夜动漫在线观看 | 日韩欧美精品一区二区三区 | 蓝军出击电视剧在线观看 | 日韩欧美网址 | 亚洲区欧美中文字幕久久 | 日韩精品一区二区三区免费观看 | 日本www网站| 榴莲视频app下载安装 | 国产手机国产手机在线 | 欧美日本一本线在线观看 | 亚洲视频欧美 | 自拍视频在线观看 | 欧美成人一区二区 | 欧美97色伦影院在线观看 | 色视频国产 | 算你色永久免费视频播放 | 免费视频色 | 亚洲欧美日韩不卡一区二区三区 | 手机看片久久国产免费不卡 | 国产手机在线视频 | 日本护士69xxxxx高清hd | 免费一区二区三区久久 | 久久精品亚洲一区二区三区浴池 | 韩国妈妈的朋友在线 | 色人阁亚洲| 欧美日韩精品一区二区在线线 | 国产成人福利免费观看 | 国产人成精品午夜在线观看 | 久色精品| 国产一级毛片网站 |